Failing function codes

Failing function codes (FFCs) identify a function within the system unit that is failing.

Table 1 describes the component that each function code identifies.

Note: When replacing a component, perform system verification for the component. See Using the diagnostics program.
Table 1. Failing function codes
FFC Description and notes
151
  1. Battery
    Note: After replacing the battery:
    1. Set the time and date.
    2. Set the Network IP addresses (for blade servers that start up from a network).
  2. System-board and chassis assembly
152 System-board and chassis assembly
166 Check management-module event log for a BladeCenter® blower or fan fault. See the documentation that comes with the BladeCenter unit.
199 System-board and chassis assembly
210 System-board and chassis assembly
212 System-board and chassis assembly (cache problem)
214 System-board and chassis assembly
217 System-board and chassis assembly
219 Common Memory Logic problem for memory DIMMs.
Note: If more than one pair of memory DIMMs are reported missing:
  1. Replace the memory DIMM at the physical location code that is reported
  2. Replace the system-board
221 System-board and chassis assembly
226 System-board and chassis assembly
227 System-board and chassis assembly
241 Ethernet network problem
282 System-board and chassis assembly
292 System-board and chassis assembly (Host – PCI bridge problem)
293 System-board and chassis assembly (PCI – PCI bridge problem)
294 System-board and chassis assembly (MPIC interrupt controller problem)
296 PCI device or adapter problem.
Note: The replacement part can only be identified by the location code reported by diagnostics.
2C4 System-board and chassis assembly
2C7 System-board and chassis assembly (Memory controller)
2C8 System-board and chassis assembly
2C9 System-board and chassis assembly
2D2 System-board and chassis assembly (Bus arbiter problem)
2D3 System-board and chassis assembly
2D4 System-board and chassis assembly (System/SP interface logic problem)
2D5 System-board and chassis assembly (I2C primary)
2D6 System-board and chassis assembly (I2C secondary)
2D7 System-board and chassis assembly (VPD module)
2D9 System-board and chassis assembly (Power controller)
2E0 System-board and chassis assembly (Fan sensor problem)
2E1 System-board and chassis assembly (Thermal sensor problem)
2E2 System-board and chassis assembly (Voltage sensor problem)
2E3 System-board and chassis assembly (Serial port controller problem)
2E4 System-board and chassis assembly (JTAG/COP controller problem)
2E8 System-board and chassis assembly (Cache controller)
308 System-board and chassis assembly (I/O bridge problem)
650 Unknown hard disk drive.
Note: This FFC indicates that the hard disk drive could not configure properly.
711 Unknown adapter
722 Unknown disk drive
7C0 System-board and chassis assembly (microprocessor/system interface)
812 System-board and chassis assembly (Common standard adapter logic problem)
814 System-board and chassis assembly (NVRAM problem)
815 System-board and chassis assembly (floating point processor problem)
817 System-board and chassis assembly (time-of-day logic)
820 System-board and chassis assembly (interprocessor related testing problem)
887 System-board and chassis assembly (integrated Ethernet adapter)
893 LAN adapter
D01 System-board and chassis assembly (cache problem)
E19 System-board and chassis assembly (power supply sensor failed)
2506 3Gb SAS pass-through expansion card
2506-101
Adapter configuration error indicated by test failures. Reconfigure the adapter. If the problem persists, replace the adapter.
2506-710
Error log analysis reveals a permanent controller failure. Replace the adapter.
2506-713
Error log analysis reveals a controller failure. Replace the adapter.
2506-720
Error log analysis reveals a controller device bus configuration error. Replace the adapter. If the problem persists, replace the system board and chassis assembly.
252B System-board and chassis assembly (SAS controller)
2567 System-board and chassis assembly (USB integrated adapter)
25A0 System-board and chassis assembly
25C4 Broadcom Ethernet adapter
2607 Emulex 8 Gb Fibre Channel expansion card (CIOv)
2624 4x InfiniBand DDR expansion card (CFFh)
2625 4x InfiniBand QDR expansion card (CFFh)
2631 System-board and chassis assembly
268B 300 GB SAS small form factor disk drive
26B4 200 GB solid-state drive
26BD Solid-state drive carrier (holds up to two solid-state drives)
26D2 600 GB SAS small form factor disk drive
2D02 System-board and chassis assembly (generic USB reference to controller/adapter)
2E00 QLogic 4 Gb Fibre Channel and Broadcom 1 Gb Ethernet expansion card (CFFh)
2E10 QLogic 4 Gb Fibre Channel and Broadcom 1 Gb Ethernet expansion card (CFFh)
2E13 QLogic 4 Gb Fibre Channel expansion card (CIOv)
2E14 QLogic 8 Gb Fibre Channel expansion card (CIOv)
2E15 QLogic 8 Gb and Broadcom 1 Gb Ethernet expansion card (CFFh)
2E21 QLogic 10 Gb FCoCEE daughtercard
2E23 QLogic 10 Gb FCoCEE daughtercard
2E33 Broadcom 4 port 1 Gb Ethernet expansion card (CFFh)
2E34 Broadcom 2 port 1 Gb Ethernet expansion card (CIOv)
2E35 QLogic 8 Gb Fibre Channel and 1 Gb Ethernet expansion card (CFFh)
2E36 System-board and chassis assembly (integrated Ethernet adapter)
Parent topic: Service request numbers (SRNs)

Notices | Terms of use | Privacy | Support