1xxxyyyy SRCs

The 1xxxyyyy system reference codes are system power control network (SPCN) reference codes.

Look for the rightmost 4 characters (yyyy in 1xxxyyyy) in the error code; this is the reference code. Find the reference code in Table 1.

Perform all actions before exchanging failing items.

Table 1. 1xxxyyyy SRCs
  • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. If an action solves the problem, then you can stop performing the remaining actions.
  • See Parts listing, type 7891 to determine which components are CRUs and which components are FRUs.
1xxxyyyy Error Codes Description Action
00AC Informational message: AC loss was reported No action is required.
00AD Informational message: A service processor reset caused the blade server to power off No action is required.
1F02 Informational message: The trace logs reached 1K of data. No action is required.
1F03 Informational message: Invalid TMS of location code. No action is required.
2600 Power good (pGood) master fault
  1. Go to Checkout procedure.
  2. Replace the base system-board (Un-P1) and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2610 pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2620 12V dc pGood input fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2622 Expansion_Comp_pGood_fault
  1. Go to Checkout procedure.
  2. Replace the expansion system-board (Un-P2) assembly, as described in Removing the expansion unit for a PS704 blade server.
  3. Replace the base system-board (Un-P1) and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2629 1.5V reg_pgood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
262B 1.8V reg_pgood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
262C 5V reg_pgood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
262D 3.3V reg_pgood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
262E 2.5V reg_pgood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
262F 1.0V fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2630 VRM CP0 core pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2632 VRM CP0 cache pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2640 VRM CP1 core pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2642 VRM CP1 array pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2647 12V "or-ing" FET short
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2648 Blade power latch fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2649 Blade power fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
265A 1.2VA pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2671 12V power fault in the blade server
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2672 CFFh expansion card voltage alert
Perform the DTRCARD symbolic CRU isolation procedure by completing the following steps:
  1. Reseat the PCIe expansion card.
  2. If the problem persists, replace the expansion card.
  3. If the problem persists, go to the Checkout procedure.
  4. If the problem persists, replace the base system-board (Un-P1) and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
The DTRCARD symbolic CRU isolation procedure is in Service processor problems
2673 Standby power fault on the expansion blade
  1. Check the management-module event log for entries that indicate a power problem with the BladeCenter® unit.
  2. Resolve any problems.
  3. Remove the blade from the BladeCenter unit and then reinsert the blade server.
  4. Power on the blade server.
  5. Monitor the blade server operation to verify that the problem is solved.
  6. If the BladeCenter unit is functioning normally, but the problem persists, replace the system board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2674 Expansion blade pGood fault at standby
  1. Go to Checkout procedure.
  2. Replace the expansion system-board (Un-P2) assembly, as described in Removing the expansion unit for a PS704 blade server.
2675 1.1 Reg_CPU0_P5IO2C_Vio_pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2676 VTTA/B pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2678 PROC Vmem controller pGood 1.0V fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
2679 Vmem_controller_pGood 1.5V reg fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
267A CFFh expansion card A0 pGood fault
Perform the DTRCARD symbolic CRU isolation procedure by completing the following steps:
  1. Reseat the PCIe expansion card.
  2. If the problem persists, replace the expansion card.
  3. If the problem persists, go to the Checkout procedure.
  4. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2-C20, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1-C20, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
The DTRCARD symbolic CRU isolation procedure is in Service processor problems
267B CFFh expansion card B0 pGood fault
Perform the DTRCARD symbolic CRU isolation procedure by completing the following steps:
  1. Reseat the PCIe expansion card.
  2. If the problem persists, replace the expansion card.
  3. If the problem persists, go to the Checkout procedure.
  4. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2-C20, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1-C20, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
The DTRCARD symbolic CRU isolation procedure is in Service processor problems
267C REG_P5IO2C_core 1.2V pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
267D 2.0_PLL_pGood fault
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
26DA pGood fault Replace the expansion system-board (Un-P2).
2900 SSD interposer card or SSD 3.3V pGood fault on the base system board Replace the following, one at a time, until the failure is no longer detected:
  1. The SSD interposer card, Un-P1-C18.
  2. The first SSD drive, Un-P1-C18-D1.
  3. The second SSD drive, Un-P1-C18-D2.
2901 SSD interposer card pGood fault Replace the interposer card on the base system planar, Un-P1-C18.
2902 SSD drive power-on self-test failure Perform one of the following actions:
  • If the location code reported with this SRC is Un-P1-C18-D1, replace the first SSD drive on the base system board.
  • If the location code reported with this SRC is Un-P1-C18-D2, replace the second SSD drive on the base system board.
2910 SSD interposer card or SSD 3.3V pGood fault on the expansion system board Replace the following, one at a time, until the failure is no longer detected:
  1. The SSD interposer card, Un-P2-C18.
  2. The first SSD drive, Un-P2-C18-D1.
  3. The second SSD drive, Un-P2-C18-D2.
2911 SSD interposer card pGood fault Replace the interposer card on the expansion system board at Un-P2-C18.
2912 SSD drive power-on self-test failure Perform one of the following actions:
  • If the location code reported with this SRC is Un-P2-C18-D1, replace the first SSD drive on the expansion system board.
  • If the location code reported with this SRC is Un-P2-C18-D2, replace the second SSD drive on the expansion system board.
3120 Voltage adjustment failure on a VMR
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
3134 Fault on the hardware monitoring chip
Perform the DTRCARD symbolic CRU isolation procedure by completing the following steps:
  1. Reseat the PCIe expansion card.
  2. If the problem persists, replace the expansion card.
  3. If the problem persists, go to the Checkout procedure.
  4. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2-C20, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1-C20, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
The DTRCARD symbolic CRU isolation procedure is in Service processor problems
8400 Invalid configuration decode
  1. Check for server firmware updates.
  2. Apply any available updates.
  3. If the problem persists:
    1. Go to Checkout procedure.
    2. Replace the system-board, as described in Replacing the FRU system-board and chassis assembly.
8402 Unable to get VPD from the concentrator
  1. Go to Checkout procedure.
  2. Replace the base system-board (Un-P1) and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
8413 Invalid processor 1 VPD
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
8414 Invalid processor 2 VPD
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
8423 No processor VPD was found
  1. Go to Checkout procedure.
  2. Replace the base system-board (Un-P1) and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
8447 SSD interposer card pGood fault Replace the interposer card on the base system planar, Un-P1-C18.
8480 Bad or missing memory controller VID
  1. Go to Checkout procedure.
  2. Perform one of the following:
    1. If the location code reported with this SRC is Un-P2, replace the expansion system-board assembly, as described in Removing the expansion unit for a PS704 blade server.
    2. If the location code reported with this SRC is Un-P1, replace the base system-board and chassis assembly, as described in Replacing the FRU system-board and chassis assembly.
Parent topic: System reference codes (SRCs)

Notices | Terms of use | Privacy | Support