IMM self tests

Use this information to resolve IMM self-test errors by referencing the error codes and following the suggested corrective actions.

Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.

See Parts listing to determine which components are consumable, structural, or CRU parts. If an action step is preceded by "(trained technician only)," that step must be performed only by a trained technician.
Error code	Description	Action
166-901-xxx	Failed the IMM test due to a failure in the Private bus (BUS 0).	Turn off the blade server, open the blade server release levers and pull the blade server away from the blade server bay, but do not remove it. See Removing the blade server from the BladeCenter unit. Wait 45 seconds and reseat the blade server in the blade server bay and turn on the blade server. See Installing the blade server in a BladeCenter unit and Turning on the blade server. Rerun the test. See Diagnostic tools overview. Make sure that the DSA Diagnostic code is up-to-date, upgrade if necessary; then, rerun the test. The latest code can be found on the IBM support website at http://www.ibm.com/ support/docview.wss? uid=psg1SERV-DSA. Make sure that the component firmware level is up-to-date, upgrade if necessary; then, rerun the test. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component. The latest level firmware for this component can be found on the IBM support website at http://www.ibm.com/ support/docview.wss? uid=psg1MIGR-4JTS2T. Turn off the blade server and reseat the blade server in the blade server bay and turn on the blade server. See Removing the blade server from the BladeCenter unit, Installing the blade server in a BladeCenter unit, and Turning on the blade server. Rerun the test. See Diagnostic tools overview. If the failure remains, refer to Removing and replacing blade server components to replace the failed component.
166-904-xxx	Failed the IMM self test due to a failure in the Lightpath bus (BUS 3).	Turn off the blade server, open the blade server release levers and pull the blade server away from the blade server bay, but do not remove it. See Removing the blade server from the BladeCenter unit. Wait 45 seconds and reseat the blade server in the blade server bay and turn on the blade server. See Installing the blade server in a BladeCenter unit and Turning on the blade server. Rerun the test. See Diagnostic tools overview. Make sure that the DSA Diagnostic code is up-to-date, upgrade if necessary; then, rerun the test. The latest code can be found on the IBM support website at http://www.ibm.com/ support/docview.wss? uid=psg1SERV-DSA. Make sure that the component firmware level is up-to-date, upgrade if necessary; then, rerun the test. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component. The latest level firmware for this component can be found on the IBM support website at http://www.http://www.ibm.com/ support/docview.wss? uid=psg1MIGR-4JTS2T. Turn off the blade server and reseat the blade server in the blade server bay and turn on the blade server. See Removing the blade server from the BladeCenter unit, Installing the blade server in a BladeCenter unit, and Turning on the blade server. Rerun the test. See Diagnostic tools overview. If the failure remains, refer to Removing and replacing blade server components to replace the failed component.
166-905-xxx	Failed the IMM self test due to a failure in the SAS/ServeRAID H1135 bus (BUS 4).	Turn off the blade server, open the blade server release levers and pull the blade server away from the blade server bay, but do not remove it. See Removing the blade server from the BladeCenter unit. Wait 45 seconds and reseat the blade server in the blade server bay and turn on the blade server. See Installing the blade server in a BladeCenter unit and Turning on the blade server. Rerun the test. See Diagnostic tools overview. Make sure that the DSA Diagnostic code is up-to-date, upgrade if necessary; then, rerun the test. The latest code can be found on the IBM support website at http://www.ibm.com/ support/docview.wss? uid=psg1SERV-DSA. Make sure that the component firmware level is up-to-date, upgrade if necessary; then, rerun the test. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component. The latest level firmware for this component can be found on the IBM support website at http://www.http://www.ibm.com/ support/docview.wss? uid=psg1MIGR-4JTS2T. Turn off the blade server and reseat the blade server in the blade server bay and turn on the blade server. See Removing the blade server from the BladeCenter unit, Installing the blade server in a BladeCenter unit, and Turning on the blade server. Rerun the test. See Diagnostic tools overview. If the failure remains, refer to Removing and replacing blade server components to replace the failed component.
166-908-xxx	Failed the IMM self test due to a failure in the EEPROM (BUS 7).	Turn off the blade server, open the blade server release levers and pull the blade server away from the blade server bay, but do not remove it. See Removing the blade server from the BladeCenter unit. Wait 45 seconds and reseat the blade server in the blade server bay and turn on the blade server. See Installing the blade server in a BladeCenter unit and Turning on the blade server. Rerun the test. See Diagnostic tools overview. Make sure that the DSA Diagnostic code is up-to-date, upgrade if necessary; then, rerun the test. The latest code can be found on the IBM support website at http://www.ibm.com/ support/docview.wss? uid=psg1SERV-DSA. Make sure that the component firmware level is up-to-date, upgrade if necessary; then, rerun the test. The installed firmware level can be found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component. The latest level firmware for this component can be found on the IBM support website at http://www.http://www.ibm.com/ support/docview.wss? uid=psg1MIGR-4JTS2T. Turn off the blade server and reseat the blade server in the blade server bay and turn on the blade server. See Removing the blade server from the BladeCenter unit, Installing the blade server in a BladeCenter unit, and Turning on the blade server. Rerun the test. See Diagnostic tools overview. If the failure remains, refer to Removing and replacing blade server components to replace the failed component.